Skip to content

Robotics

Robotics components for humanoid and dexterous systems

Printed skeletons, actuators, fingers and hands for humanoid and autonomous robots, supplied to research institutions and technology firms in the US, Europe and the UAE.

1 Skeletons

Skeletons and spines, printed as one structure

Humanoid frames, torsos and spines with flexure and lattice built into the part. Load-bearing plates and compliant segments are printed together, so there are no hinges to wear and no fasteners to loosen.

STRAIGHTFLEXED 8 DEG PER MODULE≈ 34046TPU 95A LATTICE SEGMENTBENDS AS ONE PARTPA12-CF VERTEBRA PLATECABLE CHANNEL, PRINTED INDETAIL D, LATTICE CELL6850STRUT Ø3, 45 DEGSPINE (EXAMPLE)MODULES5LATTICETPU 95A, FDMPLATESPA12-CFPARTS1 PRINTED BODYTITLEFLEXIBLE LATTICE SPINEHP3D-RB-SPN-01 REV AMM. TPU LATTICE / PA12-CFSCALE 1:2SHEET 1 OF 1
  • Lattice segments that bend as a single body
  • Cable and pneumatic routes printed inside the structure
  • Rigid plates in carbon-fibre nylon, compliant segments in TPU

2 Actuators

Actuator housings and joint modules

Housings, covers and cable guides for rotary and linear actuators, with bearing seats, gear stages and hollow bores integrated. SLS nylon prints hollow and nested geometry with no support inside the bore.

OUTPUT END VIEWAA8x Ø5.2 THRU ON Ø184 PCD(M5 CLEARANCE)6x Ø3.6 ON Ø112 PCDOUTPUT FLANGESECTION A-AØ29 HOLLOW BORE (CABLE PASS-THROUGH)12345867120.8Ø8815.2PARTS LIST1REAR COVER + ENCODER2STATOR, SLOTTED CORE3MAGNET RING4HOLLOW ROTOR HUB5PLANETARY STAGE, 9:16OUTPUT BEARING7OUTPUT FLANGE8HOUSING WALL, 6 MMDESIGN DATA (EXAMPLE)TORQUEPEAK 38 NM, RATED 12RATIO9:1, BACKLASH <0.5 DEGSPEEDNO-LOAD 240 RPM AT 48 VMASS0.62 KG, PA12-CF HOUSINGBOREØ29 HOLLOW, CABLE ROUTEPRINTEDHOUSING, COVER, GUIDEBOUGHT INMAGNETS, COILS, BEARINGTITLEROTARY JOINT ACTUATORHP3D-RB-ACT-02 REV CMM. HOUSING: PA12-CF SLSSCALE 1:1SHEET 1 OF 1
  • Hollow-bore housings for cable pass-through
  • Tight bearing and gear seats, finished to size
  • Multi-part joint modules consolidated into fewer parts

3 Fingers

Fingers with internal tendon channels

Tendon-driven finger segments with joint bores, tendon and return channels and sensor pockets in the print, at 10 micron layer height in SLA where fine detail is needed.

SIDE VIEW, PARTLY CURLEDSENSOR POCKET42.52715.5MCP JOINTØ4 H7 PIN BOREPIP JOINT Ø3 H7TENDON CHANNEL Ø1.2PALM SIDERETURN CHANNEL Ø0.8(ELASTIC CORD)GRIP TEETH, 2 MM PITCHSECTION B-B (PHALANX)15.512TENDON CHANNEL Ø1.2SENSOR CABLE DUCTRETURN CHANNEL Ø0.8DETAIL C, JOINT PIN (EXPLODED)Ø3 SS PIN, PRESS FITPTFE BUSH Ø3/Ø5FINGER DATA (EXAMPLE)DRIVEONE TENDON, THREE COUPLED JOINTSSEGMENTSSLA RESIN, 10 MICRON LAYERSPADTPU 60A, BONDEDTITLETENDON-DRIVEN FINGERHP3D-RB-FNG-03 REV AMM. SLA RESIN SEGMENTSSCALE 2:1SHEET 1 OF 1
  • Internal tendon channels, no support structure
  • Sensor pockets and cable ducts in each phalanx
  • Compliant TPU pads with printed grip texture

4 Hands

Complete dexterous hand structures

Complete hand structures: palm plate, actuator bay, thumb and four fingers with joint pins, tendon guides and wrist flange. Built for research groups developing humanoid and dexterous robots.

PALM VIEW19088TIP PAD, TPU 60A, 8 MM THICKDIP JOINT Ø3 PIN, 0-80 DEGPIP JOINT Ø3 PIN, 0-100 DEGMCP JOINT Ø4 PIN, 0-90 DEGPALM PLATE, TENDON GUIDESAND ACTUATOR BAY (PRINTED)WRIST FLANGE4x M3 ON Ø40 PCDTENDON CHANNEL Ø1.2,PRINTED, NO SUPPORTTHUMB, 5 DOFOPPOSEDHAND DATA (EXAMPLE)DOF20 ACTIVE + COUPLEDMASS0.38 KG, UNACTUATEDGRIP≈40 N AT FINGERTIPPHALANGESPA12-CF SLS, 1.6 WALLPADSTPU 60A, FDMTITLEDEXTEROUS HAND, 5 FINGERHP3D-RB-HND-01 REV BMM. PA12-CF SLS / TPU PADSSCALE 1:2SHEET 1 OF 1
  • Palm and finger structure in carbon-fibre filled nylon
  • Opposed thumb and coupled finger joints
  • Iterated in days as the design changes

Materials

Materials we print robotics in

  • TPU 95AFDM. 95A Shore, about 600% elongation at break. Feet, pads, bellows.
  • Flexible resinSLA, 10 micron layers. Fine compliant features.
  • PA12SLS. Powder supports the part, so hollow and nested geometry needs no supports.
  • PA12-CFSLS or FDM. Stiffness and low mass for frames and housings.
  • PEEKThermal stability.
  • PolyJet multi-materialSeveral materials in one build, with rubber-like options.

More on the materials guide.

Customers

Organisations that use HenleyPrint3D

  • UCL
  • Imperial College London
  • University of Cambridge
  • BBC

Robot hands, fingers, actuators and skeleton parts for research groups and technology teams in the US, Europe and the UAE.

Quote a skeleton, actuator, finger or hand

Send a file. An engineer replies with a price and lead time.

How instant 3D printing quotes work

Uploads are secure and confidential.

Related guides